2st Armor plate Bronyx CAP6 (НВМПЕ + SiC) 6th class Large

The BRONYX set includes two protective inserts rated Class 6 under DSTU 8782:2018. The model is designed to withstand high-velocity armor-piercing threats, including 7.62 × 54 mm B-32 projectiles, index 7B3-323. The inserts also provide the stated protection against lower-class threats, fragments, and ricochets. Each insert measures 260 × 330 mm and weighs approximately 3.25 kg. The set weighs about 6.5 kg. Size L is recommended for users with a chest circumference of 111–118 cm and carrier vests with matching internal compartments.

Features of BRONYX Class 6 Protective Inserts

Class 6 protection is designed for threats with high penetration capability. To achieve the stated protection level, BRONYX uses a composite system made of SiC ceramic and ultra-high-molecular-weight polyethylene. Each material acts in sequence on the projectile and the fragments created on impact.

The set includes two inserts for the front and rear compartments of a protective vest. Their matching dimensions help balance the equipment and distribute its weight between the front and rear of the torso.

Key features of the set:

• Class 6 protection under DSTU 8782:2018;
• two size L protective inserts;
• stated resistance to 7.62 × 54 mm armor-piercing projectiles;
• SiC and UHMWPE composite construction;
• designed to withstand multiple impacts under confirmed test conditions;
• angled upper corners;
• R400 anatomical curve;
• dimensions of 260 × 330 mm;
• protection against fragments and ricochets;
• manufactured in Ukraine.

The pair weighs approximately 6.5 kg, so the carrier vest should have sturdy shoulder straps and adjustable cummerbunds. For extended wear, use shoulder pads and an internal cushioning layer. Test the fully assembled equipment while moving before putting it into service.

Class 6 Protection under DSTU 8782:2018

The protective inserts meet Class 6 of the Ukrainian standard DSTU 8782:2018. Their stated specifications cover resistance to 7.62 × 54 mm B-32 armor-piercing incendiary projectiles. These projectiles have a hardened penetrator core and considerable kinetic energy.

The protection rating includes:

• 62 × 54 mm B-32;
• projectile index 7B3-323;
• lower-class threats under DSTU 8782:2018;
• fragments of various sizes;
• secondary impact elements and ricochets.

Check compliance using the markings on the inserts, the certificate, and test reports for the specific batch. Resistance is confirmed for specified projectile types and laboratory conditions. A different projectile composition, velocity, or impact angle may change the result.

Protection Against 7.62 × 54 mm B-32

The B-32 armor-piercing incendiary projectile has a hard penetrator core and an incendiary component. On contact with the insert, the front silicon carbide layer bears the greatest load. SiC’s high hardness helps fracture or damage the penetrator.

Projectile remnants and ceramic fragments are caught by the UHMWPE backing. The polyethylene layer retains them and distributes the remaining energy over a wider area. The coordinated performance of both materials provides the stated resistance to penetration.

On impact, the ceramic layer fractures locally. Even if the rear surface remains intact, the insert must be taken out of service. Only a qualified specialist can assess whether it remains suitable for use.

Multi-Impact Resistance

The model description states that the inserts can withstand multiple impacts. This resistance depends on the location of each impact, the distance between them, the angle, projectile velocity, and the area of damaged ceramic. Check the precise test conditions in the resistance test report.

A successful multi-impact test does not mean that every point provides the same level of protection after the first impact. The area around a damaged ceramic segment may have altered properties. When choosing a model, check the number of impacts, their placement pattern, and the measured backface deformation.

Silicon Carbide and UHMWPE Composite

Silicon carbide serves as a hard ceramic component. UHMWPE forms an energy-absorbing backing layer that works after the projectile contacts the front layer. The composite combines resistance to penetration with a manageable weight for size L.

The materials perform the following functions:

1. SiC receives the initial contact from the penetrator.
2. The ceramic layer helps fracture the projectile core.
3. UHMWPE retains projectile remnants.
4. The polyethylene base holds ceramic fragments.
5. The rear section distributes the remaining energy across its surface.

The integrity of the composite affects its resistance properties. A strong impact or drop may damage the ceramic inside the product. An insert suspected of having hidden cracks should be sent for professional assessment.

Size L for Increased Coverage

Each insert measures 260 × 330 mm. Size L is recommended for a chest circumference of 111–118 cm. Its increased height and width provide the coverage area suited to users who need this size.

Measure the carrier vest’s internal compartments before purchase. Size L markings may correspond to different actual dimensions across manufacturers.

Check the following measurements:

• the compartment’s internal width;
• the available pocket height;
• compatibility with the 260 × 330 mm dimensions;
• the maximum permitted thickness of the protective element;
• the shape of the upper corners;
• the area covered by the lower flap;
• available space for a cushioning insert.

The insert should fit fully inside the pocket and remain securely in place. Movement up, down, or sideways can make the equipment less stable. After installation, adjust its height with the shoulder straps and secure it with the cummerbunds.

Angled Upper Corners

The insert has angled upper corners. This shape frees up some space around the shoulder joints and makes it easier to extend the arms forward. It can be especially useful with size L inserts, which have increased width and height.

Check mobility with all pouches attached to the front panel. Excessive equipment volume can make bending and working in a prone position more difficult. If needed, move some equipment to the cummerbunds or belt.

R400 Anatomical Curve

The R400 curve indicates a 400 mm radius. This profile helps the insert sit closer to the anatomical shape of the chest. It supports a closer fit and more even pressure distribution.

Install the insert according to the markings that identify its front and rear surfaces. Orient the curve as specified by the manufacturer. After installation, adjust the front and rear inserts to the same height.

Weight of the BRONYX L Set

Each insert weighs approximately 3.25 kg. The pair weighs about 6.5 kg. Add the weight of the protective vest cover, cushioning inserts, side protection, and attached equipment to this figure.

Key size and weight specifications:

• quantity per set: 2 pcs.;
• weight of one insert: approximately 3.25 kg;
• weight of the pair: approximately 6.5 kg;
• size: L;
• dimensions: 260 × 330 mm;
• recommended chest circumference: 111–118 cm;
• shape: angled upper corners;
• curve: R400.

Account for the load when choosing a carrier vest and shoulder pads. The cummerbunds should hold the protective elements firmly against the torso. Evenly distributing equipment across the front and rear panels helps maintain balance.

Is a Cushioning Insert Needed?

7.62 × 54 mm projectiles carry high kinetic energy. After stopping a projectile, the rear surface of the insert may deform and transfer some of the load to the body. A cushioning layer helps reduce the effect of backface deformation.

If the carrier vest does not have an integrated cushioning layer, choose a separate insert. Its size should match the 260 × 330 mm format or the area of the protective insert’s rear surface. The compartment must fit both elements and close fully.

How to Install the Pair of Protective Inserts

Before installation, check the outer condition and markings on both elements. Place one insert in the front compartment and the other in the rear. The angled upper corners should face upward.

Installation steps:

1. Inspect the outer surface of both inserts.
2. Identify their front and rear surfaces.
3. Install the front protective element.
4. Place the second insert in the rear compartment.
5. Add cushioning inserts if needed.
6. Secure the lower flaps.
7. Adjust the shoulder strap height.
8. Adjust the cummerbunds.
9. Check the fit while moving.

The front and rear inserts should remain at the intended anatomical height. After adjustment, bend, squat, and move your arms actively. If the protective elements shift, adjust the compartments or fastening.

Storage and Inspection

Protective ceramic inserts from impacts, drops, and prolonged contact with moisture. Use a carrier vest, padded bag, or original packaging for transport. Store the set under the conditions specified by the manufacturer.

During inspection, check:

• the integrity of the outer cover;
• the condition of the corners and edges;
• for tears or punctures;
• that the R400 shape is intact;
• that the markings are legible;
• the date of manufacture;
• the service life.

After a strong impact or drop, visible signs of damage may not be enough to assess the ceramic’s condition. The protective element needs a specialized inspection. After an impact, discontinue its use.

Technical Specifications

The set is designed to fit the front and rear compartments of a size L carrier vest. Before ordering, compare the protective elements’ dimensions with the internal measurements of the cover.

Key specifications:

• brand: BRONYX;
• product type: protective insert set;
• quantity: 2 pcs.;
• protection class: 6;
• standard: DSTU 8782:2018;
• materials: silicon carbide (SiC) and UHMWPE;
• size: L;
• dimensions: 260 × 330 mm;
• weight of one insert: approximately 3.25 kg;
• total set weight: approximately 6.5 kg;
• recommended chest circumference: 111–118 cm;
• shape: angled upper corners;
• anatomical curve: R400;
• country of manufacture: Ukraine.

The BRONYX Large set contains two Class 6 protective inserts under DSTU 8782:2018 for the front and rear compartments of a carrier vest. Made of silicon carbide (SiC) and UHMWPE, the inserts have angled upper corners, an R400 anatomical curve, and a total weight of approximately 6.5 kg. Before ordering, check that the 260 × 330 mm dimensions fit the internal measurements of the cover.

Why Buy BRONYX Class 6 Protective Inserts from TacMed?

The TacMed online store offers a pair of BRONYX Class 6 protective inserts in size L for compatible carrier vests. The product page lists the current price, set specifications, and ordering terms. Before purchase, you can ask about certification, test results, and compatibility with a specific cover model. Delivery is available to Kyiv, Lviv, Odesa, Kharkiv, Dnipro, Zaporizhzhia, Vinnytsia, Poltava, Cherkasy, Zhytomyr, Chernihiv, Rivne, Lutsk, Ternopil, Ivano-Frankivsk, Uzhhorod, Chernivtsi, Khmelnytskyi, Kropyvnytskyi, Mykolaiv, Kherson, and other cities across Ukraine. The TacMed catalog also offers size L carrier vests, cushioning inserts, side protective packages, medical pouches, and IFAK kits.